If the nut slot is flat, then the string will rattle and buzz when played open. After each slot is cut to the right height, clean up any dust or debris. Within the 3 full-length DVDs you receive, you will learn everything from correctly restringing your guitar to adjusting actions, checking relief and more…. Start by loosening the string, not taking it off. Retune the open note and check the fretted note again. After adjusting the truss rod, clockwise to reduce relief and counter-clockwise to add relief, then reattach neck in the body with the screws and retune the strings in order to recheck the relief in the neck. If this happens you’ll have to take your guitar to an authorized Fender Service Center. Fender American Ultra Stratocaster 2019-Current, Fender American Elite Stratocaster 2015-2019, Fender American Deluxe Stratocaster 2010-2015, Fender American Deluxe Stratocaster 2004-2009 Series, Fender American Deluxe Stratocaster 1998-2003, Fender American Ultra Stratocaster Service Manual. Pull the string to the tuner. After the initial evaluation of the guitar is finished, and we didn’t run into any issues listed above, then we can continue by removing the old strings and giving the guitar a good cleanup. If the nut is too low, the string will bump into the first fret when it is played and it will "buzz," even if the rest of the instrument is properly set up and working well. So I set the front edge level with the top of the pick guard. I was just reading through the fender manual and their recommended string height for guitars above 9' radius is 1.6mm from top of 17th fret to the bottom of the string. If the nut is too high, playing at the first fret will be seriously impaired. The easiest way to do this is to capo the strings at the first fret, loosen strings at the tuner, take out neck screws, pull the neck out of the body slightly in order to adjust the neck. Start by loosening the string, not taking it off. That’s because your intonation is not set correctly. It may seem easy, and it is, but only if you take your time and allow yourself to relax and approach the project at a reasonable pace. You want the notes to ring loud and clear without any distortion or warbling, which can happen if the pickups are too close to the strings. Now with the neck straight we can check if there are any fret issues. If you don’t have a straight edge or notched ruler, you can use a capo, a .005″ feeler gauge, and your hands to check the relief of your neck. YMMV Whenever you change strings I would check all the adjustments and adjust any that are out. So, we have to adjust the intonation with a good tuner or you can simply use your ear if you have a good ear. Bass side strings are the E-A-D string and Treble side strings are the G-B-E strings. You will want to adjust the truss rod nut counterclockwise until the ruler is resting flat and even across the frets and/or fretboard. Unfortunately, most truss rod adjustments on a Stratocaster’s neck are located at the heel. String height Fender recommends that on a vintage style neck with a 7.25†radius, the bass strings should be 2mm off the neck (about 5/64 inch) and the treble strings 1.6mm (about 4/64 inch). Make sure you adjust each side of the bridge saddle evenly so that it stays level with the bridge or tremolo plate. And make sure the strap pegs and neck screws are nice and secure. If you have any reservations about performing this adjustment yourself, it is best that you save up a little bit of cash on the side and get the job done professionally, as a bad case of nerves can cause you to make a mistake. Your email address will not be published. Take the end of string and put it down into the hole of the tuner and bend it over to the right and manually wrap the string once around the tuner like the pictures show below and tune the string up. Using a ruler or a string action gauge card and holding the guitar in playing position, measure from the top of the 12th fret to the bottom of the string. Then starting at the 6th string play the open string and the play the note an octave higher at the 12th fret. (adsbygoogle = window.adsbygoogle || []).push({}); Intonation affects how well your guitar plays in tune along the entire length of the fretboard. You will first want to adjust the front edge of the bridge so that it is level with the top of the pick guard. You can use 0000 steel wool or a 320 grit Klingspor pad to polish the frets and break up any dirt that might be on the fingerboard. Your email address will not be published. Do this through your amp with the volume and tone all the way up and wide open. Remember, if you ever change string gauges you’ll have to perform this adjustment again. For the low E and A string you want to cut the string about 2 & 1/2″ behind the tuner. I used to be a full-time guitar instructor and had taught hundreds of people how to play the guitar. Don’t cut the B and high E, but just use the whole string to make sure you have the correct string break behind the nut for them since they are smaller in diameter than the wound ones. Copyright © 2020 Guitarist Lab – Privacy Policy, 10 Steps to Making a New Replacement Nut For Your Guitar. The first thing you want to do is take your feeler gauge and check the distance between the string of the first fret and the fret itself.